a review of the investigation methods and performance of pure polymer gears
Subject Areas :Rasool Molhsenzadeh 1 , ehsan nozad bonab 2
1 -
2 - Department of Mechanical Engineering, Technical and Vocational University (TVU), Tehran, 1435761137, Iran
Keywords: polymeric gear, gear performance, failure,
Abstract :
Plastic gears are widely used in various industries. The advantages of these gears include their lightness, automation, low noise, easy production and low cost. However, the high wear rate, limited working temperature and low mechanical strength in polymer gears, compared to metal types, limit their application. Therefore, extensive research has been done on the performance of polymer gears in order to identify the failure mechanisms. Among the conducted researches, the researchers focus on different parts such as determining the critical torque or in other words, load bearing capacity, gear behavior at lower and higher torques than the critical torque, gear fatigue resistance, gear wear behavior on a micro and macro scale, as well as The thermal resistance of the gear is drawn. In addition, the difference in methods and the provision of new methods for checking the mentioned factors in order to check the performance of the gear can be seen in the research. In general, the type of polymer, torque and work cycle have been recognized as factors influencing the wear of polymer gears. In this research, the method and results of the research conducted on various types of gears made with commonly used polymer materials are presented. In such a way that by comparing the performance of all types of gears, it is possible to reach a general conclusion about their use.
1. Juvinall R.C. and Marshek K.M., Fundamentals of Machine Component design, John Wiley & Sons New York, 2006.
2. Davis J.R., Gear Materials, Properties, and Manufacture. ASM International, 2005.
3. Kirupasankar S., Gurunathan C., and Gnanamoorthy R., Transmission Efficiency of Polyamide Nanocomposite Spur Gears, Materials & Design, 39, 338-343, 2012.
4. Mohsenzadeh R., Soudmand B., and Shelesh-Nezhad K., Failure Analysis of POM Ternary Nanocomposites for Gear Applications: Experimental and Finite Element Study, Engineering Failure Analysis, 140, 106606, 2022.
5. Mohsenzadeh R., Soudmand B., and Shelesh-Nezhad K., A Combined Experimental-numerical Approach for Life Analysis and Modeling of Polymer-based Ternary Nanocomposite Gears, Tribology International, 107654, 2022.
6. Kim C.H., Durability Improvement Method for Plastic Spur Gears, Tribology International, 39, 11, 1454-1461, 2006.
7. Pogačnik A. and Tavčar J., An Accelerated Multilevel Test and Design Procedure for Polymer Gears, Materials & Design, 65, 961-973, 2015.
8. Zhang Y., A Physical Investigation of Wear and Thermal Characteristics of 3D Printed Nylon Spur Gears, Tribology International, 141, 105953, 2020.
9. Li W., An Investigation on the Wear Behaviour of Dissimilar Polymer Gear Engagements, Wear, 271, 9-10, 2176-2183, 2011.
10. Mao K., The Wear and Thermal Mechanical Contact Behaviour of Machine Cut Polymer Gears, Wear, 332, 822-826, 2015.
11. Singh P.K. and A.K. Singh, An Investigation on the Thermal and Wear Behavior of Polymer Based Spur Gears, Tribology International, 118, 264-272, 2018.
12. Sarita B. and Senthilvelan S., Effects of Lubricant on the Surface Durability of an Injection Molded Polyamide 66 Spur Gear Paired with a Steel Gear, Tribology International, 137, 193-211, 2019.