A Review of Mechanical Recycling of Polylactic Acid: Challenges and Recent Achievements
Subject Areas :
1 - Research and Development Expert
Keywords: Polylactic acid, Mechanical recycling, Thermo-mechanical degradation, Waste valorization, Food packaging, 3D printing,
Abstract :
The growing use of polylactic acid (PLA) encourages technologists to conduct extensive research into valorization of PLA waste with best quality. In general, mechanical recycling of PLA is one of the most cost-effective recycling methods. However, recycled materials are commonly used for minor applications due to the inherent thermo-mechanical degradation of the polymer during recycling, which mainly results in chain scissions and intramolecular and intermolecular transesterification reactions. Therefore, it has a negative effect on the molar mass distribution and consequently on the mechanical, thermal and rheological properties of recycled PLA. In this article, a review of recent research on the effects of mechanical recycling on the properties of PLA including structural, morphological, mechanical, rheological and thermal changes was done. Furthermore, a review of three main ways of valorization of recycled PLA including thermal modification, chemical modifications in the presence of stabilizers, chain extenders, branching agents and finally mixing with nanoadditives or with other polymers was done in order to improve the properties of recycled PLA. Moreover, due to the widespread use of natural fibers to improve the performance of PLA, the recyclability of natural fiber-reinforced PLA biocomposites was investigated. Finally, two important applications of recycled PLA in the food packaging and the 3D printing industries were discussed.
1. Castro-Aguirre E., Iniguez-Franco F., Samsudin H., Fang X., Auras R., Poly (lactic acid)-Mass Production, Processing, Industrial Applications, and End of Life, Advanced Drug Delivery Reviews, 107, 333-366, 2016.
2. Farah S., Anderson D. G., Langer R., Physical and Mechanical Properties of PLA, and Their Functions in Widespread Applications-A Comprehensive Review, Advanced Drug Delivery Reviews, 107, 367-392, 2016.
3. Papong S., Malakul P., Trungkavashirakun R., Wenunun P., Chom-in T., Nithitanakul M., et al., Comparative Assessment of the Environmental Profile of PLA and PET Drinking Water Bottles from a Life Cycle Perspective, Journal of Cleaner Production, 65, 539-550, 2014.
4. Soroudi A., Jakubowicz I., Recycling of Bioplastics, Their Blends and Biocomposites: A Review, European Polymer Journal, 49, 2839-2858, 2013.
5. Piemonte V., Sabatini S., Gironi F., Chemical Recycling of PLA: A Great Opportunity Towards the Sustainable Development?, Journal of Polymers and the Environment, 21, 640-647, 2013.
6. McKeown P., Jones M. D., The Chemical Recycling of PLA: A Review, Sustainable Chemistry, 1, 1-22, 2020.
7. De Andrade M. F. C., Souza P. M., Cavalett O., Morales A. R., Life Cycle Assessment of poly (lactic acid)(PLA): Comparison Between Chemical Recycling, Mechanical Recycling and Composting, Journal of Polymers and the Environment, 24, 372-384, 2016.
8. Badia J., Ribes-Greus A., Mechanical Recycling of Polylactide, Upgrading Trends and Combination of Valorization Techniques, European Polymer Journal, 84, 22-39, 2016.
9. Badia J., Strömberg E., Ribes-Greus A., Karlsson S., Assessing the MALDI-TOF MS Sample Preparation Procedure to Analyze the Influence of Thermo-oxidative Ageing and Thermo-mechanical Degradation on Poly (Lactide), European Polymer Journal, 47, 1416-1428, 2011.
10. Cuadri A., Martín-Alfonso J., Thermal, Thermo-oxidative and Thermomechanical Degradation of PLA: A Comparative Study Based on Rheological, Chemical and Thermal Properties, Polymer Degradation and Stability, 150, 37-45, 2018.
11. Badia J., Strömberg E., Karlsson S., Ribes-Greus A., Material Valorisation of Amorphous Polylactide. Influence of Thermo-mechanical Degradation on the Morphology, Segmental Dynamics, Thermal and Mechanical Performance, Polymer Degradation and Stability, 97, 670-678, 2012.
12. Żenkiewicz M., Richert J., Rytlewski P., Moraczewski K., Stepczyńska M., Karasiewicz T., Characterisation of Multi-extruded Poly (lactic acid), Polymer Testing, 28, 412-418, 2009.
13. Beltrán F. R., Climent-Pascual E., María U., Urreaga J. M., Effect of Solid-state Polymerization on the Structure and Properties of Mechanically Recycled Poly (lactic acid), Polymer Degradation and Stability, 171, 109045, 2020.
14. Cavallo E., He X., Luzi F., Dominici F., Cerrutti P., Bernal C., et al., UV Protective, Antioxidant, Antibacterial and Compostable Polylactic Acid Composites Containing Pristine and Chemically Modified Lignin Nanoparticles, Molecules, 26, 126, 2021.
15. Pillin I., Montrelay N., Bourmaud A., Grohens Y., Effect of Thermo-mechanical Cycles on the Physico-chemical Properties of Poly (lactic acid), Polymer Degradation and Stability, 93, 321-328, 2008.
16. Benvenuta-Tapia J. J., Vivaldo-Lima E., Reduction of Molar Mass Loss and Enhancement of Thermal and Rheological Properties of Recycled Poly (lactic acid) by Using Chain Extenders Obtained from RAFT Chemistry, Reactive and Functional Polymers, 153, 104628, 2020.
17. Beltrán F. R., Infante C., Orden M. U., Urreaga J. M., Mechanical Recycling of Poly (lactic acid): Evaluation of a Chain Extender and a Peroxide as Additives for Upgrading the Recycled Plastic, Journal of Cleaner Production, 219, 46-56, 2019.
18. Tuna B., Ozkoc G., Effects of Diisocyanate and Polymeric Epoxidized Chain Extenders on the Properties of Recycled Poly (lactic acid), Journal of Polymers and the Environment, 25, 983-993, 2017.
19. López de Dicastillo C., Velásquez E., Rojas A., Guarda A., Galotto M. J., The Use of Nanoadditives within Recycled Polymers for Food Packaging: Properties, Recyclability, and Safety, Comprehensive Reviews in Food Science and Food Safety, 19, 1760-1776, 2020.
20. Beltrán F. R., Gaspar G., Chomachayi M. D., Jalali-Arani A., Lozano-Pérez A. A., Cenis J. L., et al., Influence of Addition of Organic Fillers on the Properties of Mechanically Recycled PLA, Environmental Science and Pollution Research, 28, 24291-24304, 2021.
21. Tesfaye M., Patwa R., Gupta A., Kashyap M. J., Katiyar V., Recycling of Poly (lactic acid)/Silk Based Bionanocomposites Films and its Influence on Thermal Stability, Crystallization Kinetics, Solution and Melt Rheology, International Journal of Biological Macromolecules, 101, 580-594, 2017.
22. Beltrán F. R., Arrieta M. P., Gaspar G., Orden M. U., Martínez Urreaga J., Effect of Iignocellulosic Nanoparticles Extracted from Yerba Mate (Ilex paraguariensis) on the Structural, Thermal, Optical and Barrier Properties of Mechanically Recycled Poly (lactic acid), Polymers, 12, 1690, 2020.
23. Beltrán F., De La Orden M., Urreaga J. M., Amino-modified Halloysite Nanotubes to Reduce Polymer Degradation and Improve the Performance of Mechanically Recycled Poly (lactic acid), Journal of Polymers and the Environment, 26, 4046-4055, 2018.
24. Imre B. Pukánszky B., Compatibilization in Bio-based and Biodegradable Polymer Blends, European Polymer Journal, 49, 1215-1233, 2013.
25. Liu H. Zhang J., Research Progress in Toughening Modification of Poly (lactic acid), Journal of Polymer Science Part B: Polymer Physics, 49, 1051-1083, 2011.
26. Hamad K., Kaseem M., Deri F., Effect of Recycling on Rheological and Mechanical Properties of Poly (lactic acid)/Polystyrene Polymer Blend, Journal of Materials Science, 46, 3013-3019, 2011.
27. Lopez J., Girones J., Mendez J., Puig J., Pelach M., Recycling Ability of Biodegradable Matrices and Their Cellulose-reinforced Composites in a Plastic Recycling Stream, Journal of Polymers and the Environment, 20, 96-103, 2012.
28. Le Duigou A., Pillin I., Bourmaud A., Davies P., Baley C., Effect of Recycling on Mechanical Behaviour of Biocompostable Flax/Poly (l-lactide) Composites, Composites Part A: Applied Science and Manufacturing, 39, 1471-1478, 2008.
29. Gil-Castell O., Badia J., Kittikorn T., Strömberg E., Martínez-Felipe A., Ek M., et al., Hydrothermal Ageing of Polylactide/Sisal Biocomposites. Studies of Water Absorption Behaviour and Physico-Chemical Performance, Polymer Degradation and Stability, 108, 212-222, 2014.
30. Gil-Castell O., Badia J., Kittikorn T., Strömberg E., Ek M., Karlsson S., et al., Impact of Hydrothermal Ageing on the Thermal Stability, Morphology and Viscoelastic Performance of PLA/Sisal Biocomposites, Polymer Degradation and Stability, 132, 87-96, 2016.
31. Chinthapalli R., Skoczinski P., Carus M., Baltus W., Guzman D., Käb H., et al., Biobased Building Blocks and Polymers-global Capacities, Production and Trends, Industrial Biotechnology, 15, 237-241, 2019.
32. Cecchi T., Giuliani A., Iacopini F., Santulli C., Sarasini F., Tirillò J., Unprecedented High Percentage of Food Waste Powder Filler in Poly Lactic Acid Green Composites: Synthesis, Characterization, and Volatile Profile, Environmental Science and Pollution Research, 26, 7263-7271, 2019.
33. Xiao D., Qing S., Chen P., Yu Z., Xiao H., Wang X., Development of Recycled Polylactic Acid/Oyster Shell/Biomass Waste Composite for Green Packaging Materials with Pure Natural Glue and Nano-fluid, Environmental Science and Pollution Research, 27, 26276-26304, 2020.
34. Beltrán F., Lorenzo V., Orden M., Martínez-Urreaga J., Effect of Different Mechanical Recycling Processes on the Hydrolytic Degradation of Poly (l-lactic acid), Polymer Degradation and Stability, 133, 339-348, 2016.
35. Beltrán F., Barrio I., Lorenzo V., Del Río B., Martínez Urreaga J., Orden M., Valorization of Poly (lactic acid) Wastes via Mechanical Recycling: Improvement of the Properties of the Recycled Polymer, Waste Management & Research, 37, 135-141, 2019.
36. Zhao P., Rao C., Gu F., Sharmin N., Fu J., Close-looped Recycling of Polylactic Acid Used in 3D Printing: An Experimental Investigation and Life Cycle Assessment, Journal of Cleaner Production, 197, 1046-1055, 2018.
37. Cisneros-López E., Pal A., Rodriguez A., Wu F., Misra M., Mielewski D., et al., Recycled Poly (lactic acid)–Based 3D Printed Sustainable Biocomposites: A Comparative Study with Injection Molding, Materials Today Sustainability, 7, 100027, 2020.
38. Anderson I., Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid, 3D Printing and Additive Manufacturing, 4, 110-115, 2017.